ABSTRACT
Total shoulder arthroplasty with a humeral head resurfacing (HHR) component and an inlay glenoid (OVOMotion; Arthrosurface) is a successful treatment option for patients with advanced glenohumeral arthritis, an intact rotator cuff, and adequate proximal humeral bone stock. In patients with poor proximal humeral bone, historically stemmed humeral components have been used instead of HHR. However, strategies can be used to successfully optimize HHR implant fixation in suboptimal bone without converting to stemmed implants or in surgical centers where stemmed prostheses are not available. This Technical Note describes 3 techniques-upsizing the humeral taper post, using humeral autograft, and cementation-to improve humeral implant fixation in patients with suboptimal bone stock when using the Arthrosurface OVOMotion implant.
ABSTRACT
BACKGROUND: Total shoulder arthroplasty (TSA) with a nonspherical humeral head component and inlay glenoid is a successful bone-preserving treatment for glenohumeral arthritis. This study aimed to describe the 90-day complication profile of TSA with this prosthesis and compare major and minor complication and readmission rates between inpatient- and outpatient-procedure patients. METHODS: A retrospective review was performed of a consecutive cohort of patients undergoing TSA with a nonspherical humeral head and inlay glenoid in the inpatient and outpatient settings by a single surgeon between 2017 and 2022. Age, sex, body mass index, American Society of Anesthesiologists (ASA) score, Charlson Comorbidity Index (CCI), and 90-day complication and readmission rates were compared between inpatient and outpatient groups. RESULTS: One hundred eighteen TSAs in 111 patients were identified. Mean age was 64.9 years (range, 39-90) and 65% of patients were male. Ninety-four (80%) and 24 (20%) patients underwent outpatient and inpatient procedures, respectively. Four complications (3.4%) were recorded: axillary nerve stretch injury, isolated ipsilateral arm deep venous thrombosis (DVT), ipsilateral arm DVT with pulmonary embolism requiring readmission, and gastrointestinal bleed requiring readmission. There were no reoperations or other complications. Outpatients were younger with lower ASA and CCI scores than inpatients; however, there was no difference in complications (1/24 vs. 3/94, P=1.00) or readmissions (1/24 vs. 1/94, P=0.37) between these two groups. CONCLUSIONS: TSA with a nonspherical humeral head and inlay glenoid can be performed safely in both inpatient and outpatient settings. Rates of early complications and readmissions were low with no difference according to surgical setting. Level of evidence: IV.
ABSTRACT
BACKGROUND: Unstable distal clavicular fractures treated surgically are associated with high failure rates and hardware-related complications. Newer techniques have shown promising early clinical results with fewer hardware complications; however, their biomechanical performance has not been assessed. This study biomechanically compared a distal-third locking plate with 3 newer techniques that incorporate coracoid fixation into the construct. METHODS: The study randomized 36 adult fresh frozen cadaveric shoulders to 4 groups: (1) distal-third locking plate (P); (2) distal-third locking plate with a coracoid button augmentation (P + CB); (3) coracoclavicular button (CB); and (4) coracoclavicular button with coracoclavicular ligament reconstruction using semitendinosus allograft (CB + CC). After fixation, each specimen was stressed in the coronal plane. Cyclic displacement, load at 10-mm displacement, and ultimate load to failure were measured. RESULTS: All 3 experimental groups biomechanically outperformed the locking plate. Mean load to failure was significantly higher in the CB (343 ± 76 N) and CB + CC (349 ± 94 N) groups compared with the P group (193 ± 52 N). There was also significantly less cyclic displacement in the CB (4.3 ± 1.9 mm) and CB + CC (4.4 ± 1.9 mm) groups compared with the P group (8.2 ± 2.9 mm). With respect to load at 10 mm of displacement, which essentially measures a clinical failure, the P + CB (235 ± 112 N), CB (253 ± 111 N), and CB+CC (238 ± 76 N) experimental groups significantly outperformed the P group (96 ± 29 N). CONCLUSIONS: CB and CB + CC techniques demonstrated more than 75% greater strength than the traditional locking plate alone. Coupled with greater overall construct strength and lower-profile hardware, these newer techniques may result in improved clinical outcome and fewer hardware-related complications.
